# LMTD Correction Factor Charts

Heat transfer rate in the exchanger is represented by

`q = U * A * F * LMTD`

here F (< 1) is interpreted as a geometric correction factor, that when applied to the LMTD (Log Mean Temperature Difference) of a counter flow heat exchanger, provides the effective temperature difference of the heat exchanger under consideration.

It is a measure of the heat exchanger’s departure from the ideal behavior of a counter flow heat exchanger having the same terminal temperatures. The F-LMTD method is widely used in heat exchanger analysis, particularly for heat exchanger selection, (sizing problems) when as a result of the process requirements the temperatures are known and the size of the heat exchanger is required.

Log Mean Temperature Difference is defined as

`LMTD = (ΔT`_{1} - ΔT_{2}) / ln(ΔT_{1} / ΔT_{2})

where,

`ΔT`

_{1}= T1 - t2`ΔT`

_{1}= T2 - t1

T1, T2 are inlet and outlet temperature of Fluid 1; t1, t2 are inlet and outlet temperature of Fluid 2.

Log Mean Temperature Difference Correction Factor F is dependent on temperature effectiveness P and heat capacity rate ratio R for a given flow arrangement. Temperature effectiveness P is different for each fluid of a two fluid exchanger.

For fluid 1, it is defined as the ratio of the temperature range of fluid 1 to the inlet temperature difference.

`P1 = ( T2 - T1 ) / ( t1 - T1 )`

Heat Capacity Ratio R is defined as

`R1 = ( t1 - t2 ) / ( T2 - T1 )`

### N (Shell) – 2M (Tube) Pass Tema E

Following general equation is used for shell and tube heat exchanger having N shell passes and 2M tube passes per shell.

`S = (R1² + 1)`

^{0.5}/ (R1 - 1)`W = [(1 - P1.R1)/(1 - P1)]`

^{1/N}`F = S.ln(W)/ ln[( 1 + W - S + S.W) /( 1 + W + S - S.W)]`

For limiting case of R1 = 1,

`W' = (N - N.P1)/( N - N.P1 + P1 )`

`F = 2`

^{0.5}[(1 - W')/ W' ]/ln[( W'/(1-W') + 1/2^{0.5})/( W'/(1-W') - 1/2^{0.5})]

For plotting the correction factor charts P1 values are listed from 0.01 to 1 with increment of 0.01 and then F values are calculated for each P1 and R1 based on above equations.

For following type of exchangers F values depend on NTU along with P1 and R1, where NTU is defined as number of transfer units. Range of NTU values are listed from 0.01 to 32 and F value is calculated for each value. LMTD Correction factor, F is determined as following –

`F = [ 1/(NTU1.(1 - R1))].ln[(1 - R1.P1)/(1 - P1)] ---- (1)`

For limiting case of R1 = 1,

`F = P1 / [NTU1 . (1 - P1)] ---- (2)`

### Cross Flow Fluid 1 Unmixed Tema X

Following relation is used to calculate P1 using NTU.

`K = 1 - exp(-NTU1)`

`P1 = [1 - exp(-K.R1)]/ R1`

F factor is calculated as per equations (1) & (2).

### Cross Flow Fluid 2 Unmixed Tema X

Following relation is used to calculate P1 using NTU.

`K = 1 - exp(-R1.NTU1)`

`P1 = 1 - exp(-K/R1)`

F factor is calculated as per equations (1) & (2).

### Cross Flow Both Fluid Mixed Tema X

Following relation is used to calculate P1 using NTU.

`K1 = 1 - exp(-NTU1)`

`K2 = 1 - exp(-R1.NTU1)`

`P1 = 1/[1/K1 + R1/K2 - 1/NTU1]`

F factor is calculated as per equations (1) & (2).

In a similar way, LMTD correction charts can be prepared for different type of geometries based on relation between NTU, P & R.

### Spreadsheet

Spreadsheet for LMTD Correction factor charts.

### References

- Journal of Heat Transfer, Vol. 125, June 2003 – A General Expression for the Determination of the Log Mean Temperature Correction Factor for Shell and Tube Heat Exchangers – Ahmad Fakheri
- Handbook of Heat Transfer 3
^{rd}Edition – Chapter 17 – Heat Exchangers by R.K. Shah and D.P. Sekulic

## 2 Replies to “LMTD Correction Factor Charts”

Hi!

In the spreadsheet it was not possible to choose Cross Flow Both Fluids Unmixed. Do you have a spreadsheet where you can calculate with the Cross Flow Both Fluids Unmixed?

What does the Heat Exchanger Tema X mean? What does the Cross-flow both (both unmixed, 1 mixed, both mixed) mean?